Updated Aug-2024 Exam NSE6_FWF-6.4 Dumps - Pass Your Certification Exam
Latest Real Fortinet NSE6_FWF-6.4 Exam Dumps Questions
NEW QUESTION # 10
When configuring Auto TX Power control on an AP radio, which two statements best describe how the radio responds? (Choose two.)
- A. When the AP detects any other wireless signal stronger that -70 dBm, it will reduce its transmission power until it reaches the minimum configured TX power limit.
- B. When the AP detects any wireless client signal weaker than -70 dBm, it will reduce its transmission power until it reaches the maximum configured TX power limit.
- C. When the AP detects PF Interference from an unknown source such as a cordless phone with a signal stronger that -70 dBm, it will increase its transmission power until it reaches the maximum configured TX power limit.
- D. When the AP detects any interference from a trusted neighboring AP stronger that -70 dBm, it will reduce its transmission power until it reaches the minimum configured TX power limit.
Answer: A,B
NEW QUESTION # 11
You are investigating a wireless performance issue and you are trying to audit the neighboring APs in the PF environment. You review the Rogue APs widget on the GUI but it is empty, despite the known presence of other APs.
Which configuration change will allow neighboring APs to be successfully detected?
- A. Enable Locate WiFi clients when not connected in the relevant AP profiles.
- B. Enable Radio resource provisioning on the relevant AP profiles.
- C. Enable Monitor channel utilization on the relevant AP profiles.
- D. Ensure that all allowed channels are enabled for the AP radios.
Answer: B
Explanation:
Explanation
The ARRP (Automatic Radio Resource Provisioning) profile improves upon DARRP (Distributed Automatic Radio Resource Provisioning) by allowing more factors to be considered to optimize channel selection among FortiAPs. DARRP uses the neighbor APs channels and signal strength collected from the background scan for channel selection.
NEW QUESTION # 12
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength equal to -68 dB are zoomed in to providebetter visibility.
- B. Areas with the signal strength weaker than -68 dB are highlighted in orangeand red to indicate that no signal was propagated by the APS.
- C. Areas with the signal strength weaker than -68 dB are shown with blackbackground.
- D. Areas with the signal strength equal or stronger than -68 dB are highlighted in green circles.
Answer: D
Explanation:
Explanation
The FortiPlanner site survey reading is a tool that shows the predicted signal strength of the wireless network based on the floor plan, the placement of the APs, and the propagation model. The signal strength is measured in decibels (dB), which is a logarithmic scale that indicates how much power the signal has. The higher the dB value, the stronger the signal.
The site survey reading allows the user to set a threshold value for the signal strength, which is -68 dB by default. This means that any area with a signal strength equal or stronger than -68 dB is considered to have adequate coverage for most wireless applications. These areas are highlighted in green circles on the floor plan. Any area with a signal strength weaker than -68 dB is considered to have poor coverage or no coverage at all. These areas are shown with different colors, such as yellow, orange, red, or black, depending on how weak the signal is.
Therefore, the correct answer is D. Areas with the signal strength equal or stronger than -68 dB are highlighted in green circles.
References:
FortiPlanner 2.0 User Guide, page 28
FortiPlanner Data Sheet, page 2
FortiPlanner 2.2 User Guide, page 19
NEW QUESTION # 13
Which two statements about background rogue scanning are correct? (Choose two.)
- A. Background rogue scanning requires DARRP to be enabled on the AP instance
- B. A dedicated radio configured for background scanning can detect rogue devices on all other channels in its configured frequency band
- C. A dedicated radio configured for background scanning can support the connection of wireless clients
- D. When detecting rogue APs, a dedicated radio configured for background scanning can suppress the rogue AP
Answer: C,D
Explanation:
To enable rogue AP scanning
NEW QUESTION # 14
A tunnel mode wireless network is configured on a FortiGate wireless controller.
Which task must be completed before the wireless network can be used?
- A. The new network must be manually assigned to a FortiAP profile.
- B. Security Fabric and HTTPS must be enabled on the wireless network interface
- C. The wireless network to Internet firewall policy must be configured
- D. The wireless network interface must be assigned a Layer 3 address
Answer: C
Explanation:
Explanation
A FortiGate unit is an industry leading enterprise firewall. In addition to consolidating all the functions of a network firewall, IPS, anti-malware, VPN, WAN optimization, Web filtering, and application control in a single platform, FortiGate also has an integrated Wi-Fi controller.
NEW QUESTION # 15
Which two configurations are compatible for Wireless Single Sign-On (WSSO)? (Choose two.)
- A. A VAP configured for captive portal authentication
- B. A VAP configured to authenticate locally on FortiGate
- C. A VAP configured to authenticate using a radius server
- D. A VAP configured for WPA2 or 3 Enterprise
Answer: C,D
Explanation:
Explanation
In the SSID choose WPA2-Enterprise authentication.
WSSO is RADIUS-based authentication that passes the user's user group memberships to the FortiGate.
NEW QUESTION # 16
Which statement describes FortiPresence location map functionality?
- A. Provides real-time insight into user usage stats
- B. Provides real-time insight into user movements
- C. Provides real-time insight into user purchase activity
- D. Provides real-time insight into user online activity
Answer: B
Explanation:
Explanation
(Page 88 Study Guide) "FortiPresence provides data and analytics based on demographic segmentation and visitor movement between areas" According to the web search results, FortiPresence location map functionality provides real-time insight into user movements. It uses the location data from the Fortinet access points to detect each visitor's smartphone Wi-Fi signal and track their location and behavior within the site. It also provides data visualization in a customizable format, such as heat maps and animated flows, to show the visitor traffic and movement patterns.
This geographical data analysis can help improve visitor experiences and business outcomes.
References: Location Analytics | FortiPresence 22.4.0 - Fortinet Documentation, FortiPresence Data Sheet
NEW QUESTION # 17
What is the first discovery method used by FortiAP to locate the FortiGate wireless controller in the default configuration?
- A. Static
- B. Multicast
- C. Broadcast
- D. DHCP
Answer: A
Explanation:
Explanation
According to the web search results, the first discovery method used by FortiAP to locate the FortiGate wireless controller in the default configuration is static. This means that the FortiAP sends discovery requests to a preconfigured IP address that the controller owns. This is useful if the FortiAP and the controller are not in the same subnet and other discovery methods will not work. The other discovery methods are used in sequence if the static method fails or is not configured. References: Advanced WiFi controller discovery | FortiAP / FortiWiFi 7.4.0
NEW QUESTION # 18
Refer to the exhibits.
Exhibit A
Exhibit B
The exhibits show the diagnose debug log of a station connection taken on the controller CLI.
Which security mode is used by the wireless connection?
- A. WPA2 Personal and radius MAC filtering
- B. WPA3 Enterprise
- C. Open, with radius MAC filtering
- D. WPA2 Enterprise
Answer: A
NEW QUESTION # 19
When using FortiPresence as a captive portal, which two types of public authentication services can be used to access guest Wi-Fi? (Choose two.)
- A. Hardware security token authentication
- B. Social networks authentication
- C. Software security token authentication
- D. Short message service authentication
Answer: B,D
NEW QUESTION # 20
Which administrative access method must be enabled on a FortiGate interface to allow APs to connect and function?
- A. FortiTelemetry
- B. SSH
- C. Security Fabric
- D. HTTPS
Answer: C
NEW QUESTION # 21
Refer to the exhibit.
What does the asterisk (*) symbol beside the channel mean?
- A. Indicates channels that will be scanned by the Wireless Intrusion Detection System (WIDS)
- B. Indicates channels that cannot be used because of regulatory channel restrictions
- C. Indicates channels that are subject to dynamic frequency selection (DFS) regulations
- D. Indicates channels that can be used only when Radio Resource Provisioning is enabled
Answer: C
NEW QUESTION # 22
Which statement is correct about security profiles on FortiAP devices?
- A. Security profiles on FortiAP devices can use FortiGate subscription to inspect the traffic.
- B. Security profiles can only be applied to unencrypted wireless traffic.
- C. Security profiles can only be applied via firewall policies on the FortiGate.
- D. Security profiles are only supported on Bridge-mode SSIDs.
Answer: A
Explanation:
Explanation
Security profiles are a feature that allows FortiAP devices to apply various security functions to the wireless traffic, such as antivirus, web filter, application control, intrusion prevention, and botnet scanning. Security profiles can be enabled on both tunnel-mode and bridge-mode SSIDs, and can be applied either through the wireless controller configuration or through firewall policies on the FortiGate device. Security profiles can also inspect encrypted wireless traffic, as long as the FortiAP device has access to the encryption keys.
Security profiles on FortiAP devices can use FortiGate subscription services to inspect the traffic, such as FortiGuard Antivirus, FortiGuard Web Filter, FortiGuard Application Control, and FortiGuard IPS. This means that the FortiAP device can leverage the latest threat intelligence and updates from Fortinet to protect the wireless network from malicious or unwanted content.
Therefore, the correct answer is D. Security profiles on FortiAP devices can use FortiGate subscription to inspect the traffic.
References:
FortiAP-S and FortiAP-U bridge mode security profiles
Configuring security | FortiAP / FortiWiFi 6.4.2
Security profiles - Fortinet Document Library
NEW QUESTION # 23
Which of the following is a requirement to generate analytic reports using on-site FortiPresence deployment?
- A. DTLS encryption on wireless traffic must be turned off
- B. Two wireless APs must be sending data
- C. Wireless network security must be set to open
- D. SQL services must be running
Answer: D
Explanation:
Explanation
https://docs.fortinet.com/document/fortipresence-vm/1.2.0/administration-guide/546812/introduction
NEW QUESTION # 24
When configuring a wireless network for dynamic VLAN allocation, which three IETF attributes must be supplied by the radius server? (Choose three.)
- A. 64 Tunnel-Type
- B. 83 Tunnel-Preference
- C. 58 Egress-VLAN-Name
- D. 81 Tunnel-Private-Group-ID
- E. 65 Tunnel-Medium-Type
Answer: A,D,E
Explanation:
Explanation
The RADIUS user attributes used for the VLAN ID assignment are:
IETF 64 (Tunnel Type)-Set this to VLAN.
IETF 65 (Tunnel Medium Type)-Set this to 802
IETF 81 (Tunnel Private Group ID)-Set this to VLAN ID.
NEW QUESTION # 25
What type of design model does FortiPlanner use in wireless design project?
- A. Architectural model
- B. Analytical model
- C. Integration model
- D. Predictive model
Answer: D
NEW QUESTION # 26
Which two phases are part of the process to plan a wireless design project? (Choose two.)
- A. Installation phase
- B. Hardware selection phase
- C. Site survey phase
- D. Project information phase
Answer: C,D
NEW QUESTION # 27
Which statement describes FortiPresence location map functionality?
- A. Provides real-time insight into user usage stats
- B. Provides real-time insight into user movements
- C. Provides real-time insight into user purchase activity
- D. Provides real-time insight into user online activity
Answer: B
NEW QUESTION # 28
When using FortiPresence as a captive portal, which two types of public authentication services can be used to access guest Wi-Fi? (Choose two.)
- A. Hardware security token authentication
- B. Social networks authentication
- C. Software security token authentication
- D. Short message service authentication
Answer: B,D
Explanation:
Explanation
According to the web search results, FortiPresence supports social networks authentication and short message service authentication as public authentication services for guest Wi-Fi access. Social networks authentication allows visitors to log in using their existing social media accounts, such as Facebook, Twitter, LinkedIn, Google, and Instagram. Short message service authentication allows visitors to receive a one-time password via SMS to their mobile phone number. These authentication methods are convenient and secure for visitors and provide valuable data for businesses. Software security token authentication and hardware security token authentication are not supported by FortiPresence as public authentication services for guest Wi-Fi access.
References: Configuring Captive Portal | FortiPresence 1.2.0, Configuring Captive Portal | FortiPresence
22.4.0
NEW QUESTION # 29
Which two phases are part of the process to plan a wireless design project? (Choose two.)
- A. Hardware selection phase
- B. Project information phase
- C. Site survey phase
- D. Installation phase
Answer: C,D
Explanation:
Reference:
https://www.automation.com/en-us/articles/2015-2/wireless-device-network-planning-and-design
NEW QUESTION # 30
As standard best practice, which configuration should be performed before configuring FortiAPs using a FortiGate wireless controller?
- A. Set the wireless controller country setting
- B. Create a custom AP profile
- C. Create wireless LAN specific policies
- D. Preauthorize APs
Answer: A
NEW QUESTION # 31
......
NSE6_FWF-6.4 Dumps To Pass NSE 6 Network Security Specialist Exam in One Day: https://www.passleader.top/Fortinet/NSE6_FWF-6.4-exam-braindumps.html
100% Guaranteed Results NSE6_FWF-6.4 Unlimited 37 Questions: https://drive.google.com/open?id=1ckx49Rc3b00VwCux7zfr42bGQVLh0ikd