[Jul 22, 2021] Latest CQE Exam with Accurate Quality Engineer Exam PDF Questions
Practice To CQE - PassLeader Remarkable Practice On your Quality Engineer Exam Exam
NEW QUESTION 59
A company is planning to completely change its employee performance, appraisal and reward system.
Which of the following is NOT viable for consideration in the new system?
- A. Requiring less frequent performance reviews, but utilizing many rating categories.
- B. Using continuous improvement, quality and customer satisfaction as key criteria.
- C. Integrating subordinate, peer, customer, and self-evaluations with supervisory ratings.
- D. Requiring work team or group evaluations that are equal in emphasis to individual evaluations.
Answer: A
NEW QUESTION 60
The failure rate model above is used to show a typical relationship of many parts between their failure rate and the time in service. The reliability function for period "B" is BEST represented by
- A. Option A
- B. Option D
- C. Option B
- D. Option C
Answer: B
NEW QUESTION 61
A system was designed with 3 capacitors. When the system is first activated all capacitors are operating.
The system continues to operate as long as at least 1 capacitor is operating. This is an example of
- A. An active parallel system.
- B. A standby parallel system.
- C. Redundancy.
- D. A series system.
Answer: A
NEW QUESTION 62
A "p" chart
- A. Plots the number of defects in a sample.
- B. Can be used for only one type of defect per chart.
- C. Plots variations in dimensions.
- D. Plots either the fraction or percent defective in order of time.
Answer: D
NEW QUESTION 63
Which of the following control charts are more efficient than an X-bar chart at detecting small shifts in the mean?
I. CUSUM.
II. EWQR.
III. EWMA.
- A. I and III only
- B. II only
- C. III only
- D. I only
Answer: A
NEW QUESTION 64
A typical use for the optical comparator would be to measure
- A. Surface finish.
- B. Contours.
- C. Depth of holes.
- D. Diameters of internal grooves.
Answer: B
NEW QUESTION 65
The audit team normally advises the auditee immediately upon the discovery of a finding during an audit. Which of the following items is (are) valid reasons for taking this action?
. If corrected immediately, the findings may be eliminated from the audit report.
. If corrected immediately, it shows genuine auditee interest in the objectives of the audit.
. If corrected immediately, it demonstrates the strength of an ongoing audit program.
- A. I,IIandIII
- B. I only
- C. IIandIIIonly
- D. IIIonly
Answer: C
NEW QUESTION 66
The MOST essential value of a surface plate in precision measurement application is which of the following?
- A. It provides a chemically resistant work surface.
- B. It provides a surface free of minor vibration.
- C. It provides an accurate reference surface.
- D. It provides a flat working surface.
Answer: C
NEW QUESTION 67
What are the major disadvantages of having an improvement team that is too large?
. Difficulty in having constructive input from the entire group.
. Difficulty in arriving at consensus.
. Difficulty in finding large meeting facilities.
. Difficulty, on the part of the recorder, in keeping up with more paperwork.
- A. I, II,IIIandIV
- B. I,IIandIIIonly
- C. Ionly
- D. IandIIonly
Answer: D
NEW QUESTION 68
Which of the following is a valid null hypothesis?
- A. p > 1/8
- B. mu = 110
- C. < 98
- D. The mean of population A is not equal to the mean of population B
Answer: B
NEW QUESTION 69
A single sampling plan calls for a sample size of 80 with an acceptance number of five and a rejection number of six If the quality of the submitted lots 10 percent defective. then the percent of lots expected to be accepted in the long run is approximately.
- A. 20%
- B. 30%
- C. 10%
- D. 6%
Answer: A
NEW QUESTION 70
The maximum allowable percent defective for the process average is the
- A. LPTD
- B. AOQL
- C. AQL
- D. RQL
Answer: C
NEW QUESTION 71
A process has been experiencing problems lately. The operators charting the process have identified the cause to be due to a change in incoming materials. This problem is
- A. A special cause.
- B. A common cause.
- C. Attributed to purchasing.
- D. A normal event.
Answer: A
NEW QUESTION 72
Which of the following are the MOST logical reasons for providing source inspection?
I. The supplier has consistently shown poor out-going quality.
II. The key inspection points are hidden after assembly at the suppliers' plant.
III. The supplier requests the inspection to save them potential shipping expenses.
IV. The criticality of the product warrants it.
- A. II, III and IV only
- B. I, II, III and IV
- C. II and IV only
- D. I, II and IV only
Answer: B
NEW QUESTION 73
Which of the following problem-solving tools is a column graph which displays a static picture of the process?
- A. Histogram.
- B. Pareto chart.
- C. Cause and effect diagram.
- D. Control chart.
Answer: A
NEW QUESTION 74
Given the data below is normally distributed, and the population standard deviation is 3.1, what is the 90% confidence interval for the mean?
22, 23, 19, 17, 29, 25
- A. 20.88 - 24.12
- B. 20.42 - 24.59
- C. 17.4 - 27.6
- D. 21.65 - 23.35
Answer: B
NEW QUESTION 75
An X-bar and R chart was prepared for an operation using twenty samples with five pieces in each
sample; X-bar was found to be 33.6 and R-bar was 6.20. During production, a sample of five was taken and the pieces measured 36, 43, 37, 25, and 38. At the time, this sample was taken:
- A. Both the average and range were within control limits.
- B. Only the range was outside control limits.
- C. Neither the average nor range were within control limits.
- D. Only the average was outside control limits.
Answer: B
NEW QUESTION 76
A comprehensive corrective action program is initiated at a large company. Input for CARs are received from customers, internal and external audits, material review reports and other sources. Which two of the following groups would usually administer and control the CAR process?
. Management review team.
. Quality department.
. Corrective Action Board.
. Material Review Board.
- A. I andIIIonly
- B. IIandIIIonly
- C. IIIandIVonly
- D. I andIIonly
Answer: A
NEW QUESTION 77
The AQL for a given sampling plan is 1% this means that
- A. The producer takes a small risk of rejecting product which is 1% defective or better.
- B. All lots are 1% defective or better.
- C. The average quality level of the plan is 1%.
- D. All accepted lots are 1% defective or better.
Answer: A
NEW QUESTION 78
......
Exam Questions and Answers for CQE Study Guide Questions and Answers!: https://www.passleader.top/ASQ/CQE-exam-braindumps.html
Practice To CQE - PassLeader Remarkable Practice On your Quality Engineer Exam Exam: https://drive.google.com/open?id=1NyozPUdroKowdHGGuaXIigvXezq5I2nh