NS0-521 Dumps By Pros - 1st Attempt Guaranteed Success
100% Guarantee Download NS0-521 Exam Dumps PDF Q&A
Network Appliance NS0-521 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
| Topic 6 |
|
| Topic 7 |
|
NEW QUESTION # 24
A customer asks for help cloning one database LUN from a SnapMlrror destination volume for testing the data with a new application.
What command should the administrator use to clone the LUN?
- A. lun wovestart
- B. volumeclone create
- C. volume fileclonecreate
- D. volumemove start
Answer: B
Explanation:
To clone a LUN from a SnapMirror destination volume for testing purposes, the volume clone create command should be used. This command creates a FlexClone volume from the SnapMirror destination, making the LUN within it accessible for testing without disrupting the original volume.
For more details, refer to:
* NetApp Documentation on Volume Clone Create
* NetApp Community Discussion on LUN Cloning
NEW QUESTION # 25
An administrator configured an SVM with LUNs with two WWPNs per node. The administrator accidentally created a WWPN on node1that needs to move to node2. The SAN hosts use ALUA.
Based on this requirement, what must be taken offline to correct the situation?
- A. LIF
- B. SVM
- C. LUN
- D. Volume
Answer: A
Explanation:
To move a WWPN from node1 to node2 in a NetApp ONTAP SAN environment where ALUA is used, you must take the Logical Interface (LIF) offline. Modifying LIFs involves changing their assignment between nodes, which requires them to be temporarily offline. This ensures that the path states are correctly updated without causing disruption to the SAN hosts.
For more details, see:
* NetApp Community on Moving LIFs
* NetApp Documentation on SAN LIFs
NEW QUESTION # 26
A storage engineer is required to provide NetApp site design documentation to show that the NetApp ONTAP SAN solution was delivered as intended.
Which NetApp tool can the storage engineer use to automate the creation of a difference report?
- A. Active IQ OneCollect
- B. Harvest
- C. NetAppDocs
- D. Active IQ Config Advisor
Answer: A
Explanation:
Active IQ OneCollect is a NetApp tool designed to collect configuration and performance data from your storage environment, including SAN solutions. It can automate the creation of difference reports by capturing the current state of the system and comparing it against a baseline, thereby showing any changes or deviations from the intended design.
For further details, refer to:
* NetApp Active IQ OneCollect Documentation
NEW QUESTION # 27
Click the Exhibit button.
A customer is testing a newly installed NetApp AFF A400 all-flash HA storage system. An SVM for FCP with a LUN on Node 1 has been configured, and a server has been connected as shown in the exhibit. For testing, the engineer plans to do a storage failover of Node 1.
After the failover, what is the expected status of the marked path?
- A. Offline
- B. Unavailable
- C. Active/Nonoptimized
- D. Active/Optimized
Answer: C
Explanation:
In the scenario where a storage failover is performed on Node 1 in an HA pair, the path marked in the exhibit would becomeActive/Nonoptimized. After the failover, the LIFs from Node 1 that were activeand optimized will switch to Node 2. Paths that were previously optimized will become nonoptimized because they are now served through the partner node.
For more details, see:
* NetApp Documentation on ALUA
NEW QUESTION # 28
An administrator is configuring ISCSI on an SVM and requires that all network traffic Is encrypted. What must be done to satisfy this requirement?
- A. Enable FIPS mode.
- B. Configure IPsec.
- C. Configure aggregate encryption.
- D. Use CHAP for iSCSI.
Answer: B
Explanation:
To ensure that all network traffic is encrypted for iSCSI on an SVM, configuring IPsec is required. IPsec (Internet Protocol Security) provides end-to-end encryption for IP traffic, ensuring that data transmitted over the network is secure.
For more details, refer to:
* NetApp Documentation on Configuring IPsec
NEW QUESTION # 29
A NetApp AFF node in a four-node cluster has a single FC port on one node, which Is used for legacy tape backup. Tape is no longer needed, and the port is disconnected and modified for reuse in the FCP SAN.
Based on this change, which command will verify that the port is usable?
- A. syszem node hardware unified-connect show
- B. networkinterface show
- C. vserver fcp initiator show
- D. lun persistent-reservationshow
Answer: A
Explanation:
To verify that a modified FC port is usable after it has been repurposed from tape backup to FCP SAN, the command system node hardware unified-connect show should be used. This command checks the status and configuration of the unified connect hardware, ensuring that the port is correctly set up for the new function in the SAN environment.
For additional details, see:
* NetApp Command Reference
NEW QUESTION # 30
During maintenance of A NetApp AFF ONTAP cluster, which two steps are needed to move the SAN UFs to new nodes that are members of a portset? (Choose two.)
- A. Disable the zoning of the LIF WWPN.
- B. Disable the SLM feature for the node that hosts the LIF.
- C. Take the SAN LIF offline.
- D. Remove the LIF from the portset.
Answer: C,D
NEW QUESTION # 31
A customer has a two-node NetApp ONTAP cluster that Is hosting FC LUNs for 64 SAN hosts. An administrator is tasked to add 40 more hosts to the environment.
What two actions would the administrator need to take to avoid potential performance problems with the environment? (Choose two.)
- A. Configure additional FC ports on existing hosts.
- B. Configure a higher queue depth on the target ports.
- C. Configure additional FC target ports.
- D. Configure additional SAN LIFs.
Answer: C,D
Explanation:
When adding 40 more hosts to a two-node NetApp ONTAP cluster that is already hosting 64 SAN hosts, the following actions are necessary to avoid potential performance problems:
* Configure additional FC target ports: Increasing the number of Fibre Channel (FC) target ports on the storage nodes will help distribute the I/O load more evenly, reducing the risk of bottlenecks.
* Configure additional SAN LIFs: Adding more SAN Logical Interfaces (LIFs) will ensure that the increased number of hosts can connect efficiently, improving load balancing and path management.
These actions help maintain optimal performance and prevent congestion in the SAN environment.
For more detailed guidance, refer to:
* NetApp SAN Host Configuration Overview
* NetApp Best Practices for SAN (NetApp) (NetApp)
NEW QUESTION # 32
What Is the storage construct that enables an NVMe client to store data in an SVM?
- A. Namespace
- B. FlexGroup volume
- C. Subsystem
- D. LUN
Answer: C
Explanation:
In an NVMe environment, the storage construct that enables an NVMe client to store data in an SVM (Storage Virtual Machine) is aSubsystem. A subsystem is a collection of one or more namespaces, which are used to store data. This abstraction allows for efficient management and scaling of NVMe storage within the ONTAP environment.
For further information, refer to:
* NetApp NVMe/FC Configuration (NetApp).
NEW QUESTION # 33
An administrator has a NetApp AFF cluster with two SVMs serving LUNs. SnapMirror active sync is configured, and a disaster recovery test is planned over the weekend.
Which NetApp ONTAP command will show the status of this test?
- A. snapmirror failover show
- B. storage failover hwassist show
- C. snapnirror config-replication status show
- D. network interface failover-groups show
Answer: A
Explanation:
To check the status of a SnapMirror active sync disaster recovery test on a NetApp ONTAP cluster, you would use the command snapmirror failover show. This command provides the necessary details about the failover status, helping administrators verify if the disaster recovery test is proceeding as expected. It displays the status of the failover groups and their readiness, which is essential for confirming the effectiveness of the disaster recovery setup.
For more detailed information on SnapMirror commands and their usage, refer to:
* NetApp Documentation - SnapMirror Commands (NetApp Community) (NetApp Community).
NEW QUESTION # 34
A customer has data in a LUN on an existing third-party SAN storage system that will be migrated to a new NetApp AFF A400 all-flash MetroCluster system. The host connected to the LUN is a Windows Server 2019 system.
In this scenario, which two methods are supported? (Choose two.)
- A. SnapMirror Business Continuity
- B. Foreign LUN Import in offline mode
- C. Foreign LUN Import in online mode
- D. Client-side copy of the data
Answer: B,C
Explanation:
To migrate data from a LUN on an existing third-party SAN storage system to a new NetApp AFF A400 all-flash MetroCluster system, the supported methods include:
* Foreign LUN Import in online mode: This method allows for data migration without significant downtime, enabling the system to continue serving data while the migration process is ongoing.
* Foreign LUN Import in offline mode: This method involves taking the LUN offline during the migration process, which may be necessary in certain scenarios to ensure data integrity.
For more details, refer to:
* NetApp Documentation on Foreign LUN Import
* NetApp Community on LUN Import Methods
NEW QUESTION # 35
An administrator upgraded their NetApp ONTAP software from release 9.10.1 to 9.13.1 on a NetApp All SAN Array (ASA) cluster and is creating a new iSCSI SVM.
Which automatic feature can be used with iSCSI?
- A. LIF failover
- B. igroup creation
- C. CHAP authentication
- D. LUN mapping
Answer: A
Explanation:
In NetApp ONTAP 9.13.1, one of the automatic features that can be used with iSCSI isLIF failover. This feature ensures that in the event of a network failure or a node issue, the Logical Interface (LIF) will automatically fail over to another available port, maintaining connectivity and minimizing disruption to iSCSI traffic.
For more information, refer to:
* NetApp ONTAP 9.13.1 Features
NEW QUESTION # 36
When using tagged VLANs on Cisco Nexus switches for NVMe over TCP, which two changes must be made to enable jumbo frames? (Choose two.)
- A. Modify the appropriate broadcast domain in NetApp ONTAP software to use an MTU of 9216.
- B. Modify the Cisco Nexus switches to use an MTU of 9000.
- C. Modify the Cisco Nexus switches to use an MTU of 9216.
- D. Modify the appropriate broadcast domain in NetApp ONTAP software to use an MTU of 9000.
Answer: A,C
Explanation:
For enabling jumbo frames on Cisco Nexus switches for NVMe over TCP with tagged VLANs, the following changes are required:
* Modify the Cisco Nexus switches to use an MTU of 9216: Setting the MTU to 9216 ensures that the network can handle jumbo frames, reducing the number of packets needed for large data transfers and thus improving performance.
* Modify the appropriate broadcast domain in NetApp ONTAP software to use an MTU of 9216:
This setting must match the network configuration to ensure end-to-end support for jumbo frames, which is essential for optimizing performance in NVMe over TCP environments.
For additional information, refer to:
* NetApp Documentation on NVMe over TCP
* Cisco Documentation on Jumbo Frames
NEW QUESTION # 37
A customer wants to enable CHAP authentication on their iSCSI sessions.
Which command should be used to set up the appropriate security policies and passwords?
- A. igroup initiator modify
- B. security certificate create
- C. vserver iscsi security create
- D. security login create
Answer: C
Explanation:
To enable CHAP (Challenge-Handshake Authentication Protocol) authentication on iSCSI sessions, the command vserver iscsi security create should be used. This command sets up the necessary security policies and passwords required for CHAP authentication, ensuring secure access to iSCSI targets.
For more details, refer to:
* NetApp Documentation on iSCSI Configuration (NetApp).
NEW QUESTION # 38
An administrator runs the lun igroup show -insrar.ee command on a NetApp ONTAP SAN.
Based on the output, what is the initiator type?
- A. WWPN
- B. WWNN
- C. NQN
- D. IQN
Answer: A
Explanation:
Based on the output of the command lun igroup show -instance, which lists the protocol as fcp and the initiator as server1.netapp.com, the initiator type is WWPN (World Wide Port Name). In Fibre Channel Protocol (FCP) environments, WWPNs are used to uniquely identify Fibre Channel devices. This contrasts with IQNs used in iSCSI, and NQNs used in NVMe over Fabrics.
For more details, refer to:
* NetApp Documentation on Initiators
NEW QUESTION # 39
Acustomer currently operates a legacy iSCSI storage environment that is connected to network switches with several Windows hosts. As part of an upcoming NetApp ONTAP software upgrade, an engineer needs to verify compatibility.
Which two NetApp tools would help the engineer assess the environment? (Choose two.)
- A. Hardware Universe
- B. Interoperability Matrix Tool
- C. BlueXP classification
- D. Active IQ OneCollect
Answer: B,D
Explanation:
To verify compatibility in an iSCSI storage environment before a NetApp ONTAP software upgrade, the following tools are recommended:
* Interoperability Matrix Tool (IMT): This tool helps verify the compatibility of different components, including network switches, hosts, and storage systems, ensuring that the planned upgrade will be supported.
* Active IQ OneCollect: This tool collects comprehensive configuration and performance data from the storage environment, which can be used to assess the current setup and identify any compatibility issues before the upgrade.
For further details, refer to:
* NetApp Interoperability Matrix Tool
* Active IQ OneCollect Documentation
NEW QUESTION # 40
A healthcare customer wants to Implement an FC SAN solution consisting of a NetApp ONTAP system, Broadcom switches, and servers.
Which tool contains detailed blueprints and implementation references that can be used to design this solution?
- A. NetApp Active IQ Unified Manager
- B. NetApp Fusion
- C. NetApp Active IQ Config Advisor
- D. NetApp Verified Architecture
Answer: D
Explanation:
The correct tool for designing an FC SAN solution consisting of a NetApp ONTAP system, Broadcom switches, and servers is the "NetApp Verified Architecture" (NVA). The NetApp Verified Architecture provides comprehensive blueprints and detailed implementation references. These blueprints are thoroughly tested, prescriptive in nature, and designed to minimize deployment risks and accelerate time to market. They are specifically designed to help ensure that the architecture meets the high standards required for enterprise environments.
NVA documents include design guides, best practices, and detailed configuration steps, making them invaluable for planning and deploying complex solutions like the one described.
For more information, you can refer to the official NetApp documentation on NetApp Verified Architectures:
* NetApp Verified Architecture Program Summary
* NetApp Verified Architecture Overview
These resources provide detailed insights into the architecture, including technology requirements, deployment procedures, and additional references for further reading.
NEW QUESTION # 41
An engineer Is implementing a data migration scenario for a customer who has multiple FC LUNs across multiple third-party SAN arrays. The engineer wants to use Foreign LUN Import (FLI) for the migration.
What is a requirement on the destination NetApp ONTAP cluster for FLI?
- A. A valid SnapMirror license
- B. At least one FC port in target mode
- C. A valid NetApp XCP license
- D. At least one FC port in initiator mode
Answer: B
Explanation:
When using Foreign LUN Import (FLI) for migrating LUNs from third-party SAN arrays to a NetApp ONTAP system, one of the requirements is to have at least one Fibre Channel (FC) port configured in target mode on the destination NetApp ONTAP cluster. This configuration is necessary to facilitate the migration process as the target mode port will accept and manage incoming data from the source SAN arrays.
For additional details, refer to:
* NetApp Documentation on FLI
NEW QUESTION # 42
An administrator finishes an installation of a new NetApp ASA system at the customer site and creates a new LUN. The customer wants to restrict the access of the LUN to specific UFs.
Where would the administrator configure this?
- A. Selective LUN Map
- B. Portset
- C. igroup
- D. Zoning
Answer: C
Explanation:
To restrict access to a newly created LUN to specific hosts, the administrator should configure theigroup (initiator group). An igroup is used to control which initiators (hosts) are allowed to access specific LUNs.
This ensures that only authorized hosts can access the storage, enhancing security and access control.
For more details, refer to:
* NetApp Documentation on iGroups (NetApp).
NEW QUESTION # 43
What connectivity Is required between NetApp ONTAP clusters in order to configure SnapMirror active sync across two data centers for FC?
- A. Shared FC switches
- B. Dedicated IP switches and ISL
- C. Cluster peering
- D. Cedicated FC switches and ISL
Answer: C
Explanation:
To configure SnapMirror active sync across two data centers using FC (Fibre Channel), the required connectivity between NetApp ONTAP clusters is cluster peering. Cluster peering involves establishing a trust relationship between the clusters, allowing them to replicate data seamlessly. This setup ensures that data synchronization and disaster recovery processes are effective and reliable.
For more detailed information, you can check:
* NetApp Documentation on SnapMirror and Cluster Peering
NEW QUESTION # 44
A storage administrator has a NetApp AFF SAN cluster in a multitenant environment. Another user has requested access to perform only replication within a specific SVM to another cluster.
Which default role would be used in this scenario?
- A. vsadmin-backup
- B. vsadmin-protocol
- C. backup
- D. readonly
Answer: A
Explanation:
In a multitenant environment where a user needs access only to perform replication within a specific SVM to another cluster, the default rolevsadmin-backupis appropriate. This role provides thenecessary permissions to manage backup and replication tasks without granting broader administrative rights.
For more details, see:
* NetApp Documentation on User Roles
* NetApp Community Discussion on Roles
NEW QUESTION # 45
What Is modified when moving a LUN between different HA pairs in the same SVM to prevent loss of connectivity?
- A. reporting nodes
Cigroup - B. port name
- C. LUN mapping
Answer: A
Explanation:
When moving a LUN between different HA pairs in the same SVM to prevent loss of connectivity, the reporting nodes must be modified. The reporting nodes configuration ensures that the initiator paths are properly updated to reflect the new physical location of the LUN. This prevents disruptions in connectivity by maintaining the correct pathing information for the host systems accessing the LUN.
For more details, refer to:
* NetApp Documentation on LUN Management
NEW QUESTION # 46
Which feature enables simultaneous snapshots of multiple LUNs In different volumes?
- A. Failover groups
- B. SyncMirror
- C. Single File SnapRestore
- D. Consistency groups
Answer: D
Explanation:
The feature that enables simultaneous snapshots of multiple LUNs in different volumes isConsistency Groups
. This feature ensures that snapshots taken across different LUNs and volumes are consistent with each other, making it possible to recover a consistent state across multiple storage objects.
For further information, refer to:
* NetApp Documentation on Consistency Groups
NEW QUESTION # 47
......
Earn Quick And Easy Success With NS0-521 Dumps: https://www.passleader.top/NetworkAppliance/NS0-521-exam-braindumps.html
Kickstart your Career with Real Updated Questions: https://drive.google.com/open?id=1FPuwQ2I-SEl_iWoWJO1zxDOHhfFDMQfJ